Search Results

Standard

Packaging, Storage, and Shelf Life of Hydraulic Brake Hose Assemblies

2005-10-18

HISTORICAL

J1288_200510

This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.

Standard

Vacuum Brake Hose

2005-03-30

HISTORICAL

J1403_200503

The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on vacuum lines of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.

Standard

Moisture Transmission Test Procedure—Hydraulic Brake Hose Assemblies

2003-07-30

HISTORICAL

J1873_200307

This SAE Recommended Practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which is intended to provide the user with a method of comparing the ability of hydraulic brake hose designs to retard the ingress of moisture into brake fluid. This document specifies a laboratory performance requirement. ASTM D 1364 Interlaboratory reproducibility and correlation of data have not been defined, nor has correlation been established between field vehicle brake fluid moisture content and data obtained by this document.

Standard

Road Vehicle—Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

2003-06-10

HISTORICAL

J1401_200306

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a 3.5 mm or less (1/8 in or less) b 4 to 5 mm (3/16 in)

Standard

Automotive Hydraulic Brake System—Metric Banjo Bolt Connections

2002-10-31

HISTORICAL

J1291_200210

This SAE Standard documents dimensional metric specifications for hydraulic brake system threaded ports and banjo bolts for the interconnection of major components in automotive hydraulic brake systems. Banjo blocks are not covered by this document. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices). Some applications may require sizes or forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

Automotive Hydraulic Brake System—Metric Tube Connections

2002-10-31

HISTORICAL

J1290_200210

This SAE Standard documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with International Organization for Standardization Specification, ISO 4038. Some applications may require sizes of forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

Application of Hydraulic Brake Hose to Motor Vehicles

2002-04-09

HISTORICAL

J1406_200204

This SAE Recommended Practice covers the application of hydraulic brake hose (as defined by current issue of SAE J1401) as used to provide a flexible hydraulic connection between brake system components on motor vehicles.

Standard

Moisture Transmission Test Procedure—Hydraulic Brake Hose Assemblies

2000-10-01

HISTORICAL

J1873_200010

This SAE Recommended Practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which is intended to provide the user with a method of comparing the ability of hydraulic brake hose designs to retard the ingress of moisture into brake fluid. This document specifies a laboratory performance requirement. ASTM D 1364 Interlaboratory reproducibility and correlation of data have not been defined, nor has correlation been established between field vehicle brake fluid moisture content and data obtained by this document.

Standard

Road Vehicle—Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

1999-09-09

HISTORICAL

J1401_199909

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a 3.5 mm or less (1/8 in or less) b 4 to 5 mm (3/16 in)

Standard

Packaging, Storage, and Shelf Life cf Hydraulic Brake Hose Assemblies

1999-04-01

HISTORICAL

J1288_199904

This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.

Standard

Power Steering Pressure Hose—Wire Braid

1998-05-01

HISTORICAL

J190_199805

This specification covers hose fabricated from wire braid and synthetic rubber, assembled with end fittings for use in automotive applications up to 10.3 MPa (1500 psi) maximum pressure, as flexible connections within the temperature range of −40 °C to 121 °C (−40 °F to +250 °F) average, 13.5 °C (275 °F) maximum peaks. The specification in this SAE Standard originated in the SAE-ASTM Technical Committee on Automotive Rubber (other than tires). They represent the correlation of the best information available from research investigation and production experience on the minimum constructional and performance characteristics essential for new power steering assemblies used as original or replacement equipment. This standard applies to passenger cars. It may prove useful to truck manufacturers, but it is not to be presented as present practices.

Standard

RUBBER SEALS FOR HYDRAULIC DISC BRAKE CYLINDERS

1995-01-10

HISTORICAL

J1603_199501

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

ROAD VEHICLE–HYDRAULIC BRAKE HOSE ASSEMBLIES FOR USE WITH NONPETROLEUM-BASE HYDRAULIC FLUIDS

1994-06-01

HISTORICAL

J1401_199406

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall be one of the following values: a 3.2 mm (1/8 in) or, b 4.8 mm (3/16 in)

Standard

RUBBER DUST BOOTS FOR THE HYDRAULIC DISK BRAKE PISTON

1991-09-30

HISTORICAL

J1570_199109

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of −40 to + 120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

Standard

Road Vehicle--Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

1990-06-01

HISTORICAL

J1401_199006

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: 3.5 mm or less (1/8 in or less) 4 to 5 mm (3/16 in)

Standard

VACUUM BRAKE HOSE

1989-07-01

HISTORICAL

J1403_198907

The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on transmission lines in combinations of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.

Standard

APPLICATION OF HYDRAULIC BRAKE HOSE TO MOTOR VEHICLES

1989-05-01

HISTORICAL

J1406_198905

This recommended practice covers the application of hydraulic brake hose (as defined by SAE J1401 JUN85, Road Vehicle - Hydraulic Brake Hose Assemblies for Use with Nonpetroleum Base Hydraulic Fluids) as used to provide a flexible hydraulic connection between the brake system components on motor vehicles.

Standard

HOT IMPULSE TEST FOR HYDRAULIC BRAKE HOSE ASSEMBLIES

1988-11-01

HISTORICAL

J1833_198811

This recommended practice describes the equipment, test procedure, and performance requirements for high temperature impulsing of automotive brake hose assemblies with hydraulic brake fluid.

Standard

Dynamic Ozone Test Procedure--Hydraulic Brake Hose

1988-06-01

CURRENT

J1914_198803

The purpose of this recommended practice is to evaluate in the laboratory the effect of flexing on a brake hose when exposed to a high ozone concentration environment. This recommended practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which subjects the hose to dynamic ozone exposure.

Standard

MOISTURE TRANSMISSION TEST PROCEDURE - HYDRAULIC BRAKE HOSE ASSEMBLIES

1988-03-01

HISTORICAL

J1873_198803

This recommended practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test, which is intended to subject the hose to moisture transmission equivalent to that expected during the life of the vehicle.